Oletko Viranomainen? Meiltä 10% Viranomais­alennus lähes kaikkiin tuotteisiin - Katso ohjeet »
Lajit‪» Viranomaistuotteet‪» Optiikka‪» Renkaat ja tarvikkeet‪» Riserit‪»

BCM A/T™ Optic Riser 525-11

BCM A/T™ Optic Riser 525-11

BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11
BCM A/T™ Optic Riser 525-11

Hinta
129,90 sis. alv 24% (104.76 €, alv 0) + toimituskulut


Määrä
kpl



Tulossa lisää arviolta 10.5.2024
Myymälä (Helsinki)hyllyssä0 kpl
Netistä toimitettavissa0 kpl

Saatavuus
Arviolta 60 - 120 vrk tilauksesta. Arvion luotettavuus on melko hyvä.

Varastotilanne ja saapuvat
Haluan ilmoituksen, kun tuotetta tulee lisää varastoon


Tuotteen kuvaus
A/T Optic Riser 525-11 is approximately 4-1/2” long and is intended to be used with an optic backed up by a magnifier or NVG or thermal depending on the number of recoil slots the mount takes up.  This riser has 11 recoil slots (12 lugs).

BCM® A/T™ Riser

Ideal for layering magnifiers and other enhancement systems with red dot optics, BCM A/T Risers offer the potential for a more capable platform that can improve threat identification in complex settings. 

BORNE FROM EXPERIENCE

Optimized for close combat ranges, the BCM A/T Riser creates a platform that raises the centerline of attached optics and magnifiers by approximately 1/2 inch. This additional height enhances the trained end user’s situational awareness, and further, makes it possible for them to take better aimed shots if they are using the optic in conjunction with night vision or other PPE systems.

Interfacing with the upper receiver using the same low-profile A/T system used in our Optic Mounts, not only reduces snag hazards but makes the entire length of rail usable for either bolt-on or QD attachments. Further, the low profile A/T interface enables mounting accessories with Mil-Std 1913 attachments anywhere on the stalk of the riser platform allowing end users to fine tune placement of optics, magnifiers, and other accessories.

Each A/T Riser is machined from aircraft aluminum alloy, hard coat anodized per Mil-A-8625F. The steel alloy clamp is hardened with Nitride coating for maximum strength. Finally, each Riser features multiple integral recoil lugs to mitigate recoil and counter recoil to preserve your zero and ensure “no fail” shots are placed where intended by the trained rifleman.

Valmistusmaa
Yhdysvallat


Kommentit
Lisää kommentti

Tuotemerkki